| Cutting Width | 3.6 m |
| Cutting Height | 2.2 m - 4.7 m |
| High Flit Speed | >20m/minute |
| Ground Pressure | <200kPa |
| Dust Suppression | <TLV 2mg/m3 |
| Grade | 1:6 both longitude and latitude |
| Radio Remote Control | Pempek |
| Incoming Supply | 1,000v |
| Roof Fall Protection & Rub Rail System | Robust roof and rib sprawl protection and a rub rail system on each side of the miner |
| Power Tram Connectivity | Tram by use of a Power Tram |
| Gas Monitoring | Methane & Oxygen monitors |
| Camera's | 3 x cameras - 2 facing towards the cutting face and 1 facing outbye |
| Communication System | Serial, fibre |
| Hitch Point | The Hitch Point is compatible with the Plunge Conveyor connection point and rated for the recovery of the system at 2.0 time the mass on the miner. |
| System Compatibility | Compatibility between Continuous Haulage System and Remote Operating Centre |
| Remote Control | AS 4240 compliant |
| Remote Operations | Full functional operation of the machine from the ROC utilizing a primary control (Ethernet) and have the capability of switching to secondary controls such as serial communications (such as power cable pilot), pendant control of wireless remote control. |
| 3rd Party Guidance System | Installation/integration of LN270 Miner Position Measurement System (CMPMC) hardware/software components |
| Gamma Sensor | Installation/integration of Miner Gamma coal thickness sensor and hardware components |
| Maximum Grade | 1:6 both longitude and latitude |
| Hydraulic Dewatering System | Fitted with 2 x hydraulics dewatering pumps located on the outbye side of the shovel and operated remotely from the ROC. |
| Belt Width | 1,200 mm |
| Belt Speed | 4 m/s |
| Side Skirt Depth | 300 mm |
| Power | 15.5 kW |
| Capacity | up to 2,500 tph** |
* Per each conveyor module
**Subject to ROM size distribution
| Length - Overall | 9.5 m |
| Length - Centre to Centre | 7.5 m* |
| Width | 2.5 m |
| Height (max) | 2 m |
| Wheel Size | 33x12-20 F2A Pattern |
| Wheel Diameter | 837 mm |
| Wheel Width | 290 mm |
| Tramming Speed - travel | 20 m/min |
| Tramming Speed - operating | as low as 0.33m/min** |
| Slew Ring Diameter | 1,161mm |
Electricals Smart Car Module
Each Car/Module has a flame proof electrical enclosure with PLC controller internal.
- Each Car/Module operates as a "Smart Car/Module" with all control functions internal to its system.
- The PLC controller controls all field devices and solenoid functions and receives encoder feedback from traction and steering and related devices - and controls sequencing for conveyor starts and stops and other control and monitoring functions.
- The PLC controller is linked into the System Control Computer located within the Main Control Panel / Enclosure.
* Centre of pivot to centre of pivot
**When following Continuous Miner cutting cycles
| Belt Width | 1,200 mm |
| Belt Speed | 4 m/s |
| Troughing Angle | 30° |
| Main Control Panel/Enclosure | Main Control Panel / Enclosure located on rear of Pump Station/Services Module including 3x250kW starters, main circuit breaker, HMI (PLC with display), solenoid control functions for Pump Station/Services Module, belt field devices and hydraulic function controls for side discharge conveyor. This also integrates fault finding systems/codes to simplify maintenance and repairs. |
| System Voltage | 1,000v |
| Outbye Pump Station | 3 x 250 kW |
| Mains Pressure | 400 bar |
| Outbye Storage Volue | 2,000 ltrs |
| Car/Module Pressure | 350 bar |
| Car/Module Storage | 100 ltr |
